You should see the massive Antenna wire I just ran at my house with those connectors for my future ham radio install. This cable is huge with the connectors to match. Now I just need to get off my tush and get my FCC license.
--- In Avid-L2@yahoogroups.com, "Mikeparsons.tv" <mikeparsons.tv@...> wrote:
>
> I have a box of spare pl259 terminators if you need them. I know they will come in hand one day.
>
> Mike
>
> > On 13 Dec, 2013, at 6:59 am, "johnrobmoore" <bigfish@...> wrote:
> >
> > I've had several issues with unterminated HDSDI. The 2 sdi inputs on the common JVC DTV LED monitors only terminate the active input. When I've looped the inputs through a scope and then terminate at the monitor I can only properly scope the active input. Usually input 1/A is the NLE output and 2/B is Record VTR back. If I set the scope to A and but the monitor on input 2 the A loop is unterminated and the scope goes nuts. My solution has been 2 DAs so I don't have to loop.
> >
> > I also tried once to take a little bnc rotary switch box from Fry's and use it to A B switch between the HDSDI output of a classic Nitris with it's SDSDI output. It didn't work at all even the SDSDI was twitchy beyond belief. Perhaps different output chip sets have more tolerance but in Avid world I would have never thought about a T bnc. Maybe double terminating has less ramifications than unterminating.
> >
> > Time for me to go solder some 600 ohm termination resistors into the XLR audio inputs on my VTR 2B. ;-)
> >
> > --- In Avid-L2@yahoogroups.com, "Mikeparsons.tv" <mikeparsons.tv@> wrote:
> > >
> > > It will make bob Zellin cry but stick a bnc t splitter in - you're not overly worried about termination in sdi these days.
> > >
> > > Mike
> > >
> > > > On 13 Dec, 2013, at 3:27 am, Lou Wirth <loutv@> wrote:
> > > >
> > > > Source is Mojo DX coming out to my Flanders HD monitor. Mojo has one output I think so that is where it starts.
> > > >
> > > >
> > > > Lou
> > > > Lou Wirth Productions
> > > > 500Tamal Plaza, Suite 522
> > > > Corte Madera, CA 94925
> > > > www.louwirth.com
> > > > 415-924-9411p
> > > >
> > > >
> > > >
> > > >
> > > >
> > > >> On Dec 12, 2013, at 12:01 PM, Mark Spano <cutandcover@> wrote:
> > > >>
> > > >>
> > > >>
> > > >> Lou, I'm curious what your source signal is coming from. Surely if it's your Avid, you have either a Nitris DX (which can do live downconvert) or some Blackmagic/AJA hardware (which can also do live downconvert)?
> > > >>
> > > >>
> > > >>> On Thu, Dec 12, 2013 at 1:58 PM, Lou Wirth <loutv@> wrote:
> > > >>>
> > > >>> That will do it. Thanks!
> > > >>>
> > > >>>
> > > >>>
> > > >>> Lou Wirth Productions
> > > >>> 500Tamal Plaza, Suite 522
> > > >>> Corte Madera, CA 94925
> > > >>> www.louwirth.com
> > > >>> 415-924-9411p
> > > >>>
> > > >>>
> > > >>>
> > > >>>
> > > >>>
> > > >>>> On Dec 12, 2013, at 10:26 AM, Bogdan Grigorescu <bogdan_grigorescu@> wrote:
> > > >>>>
> > > >>>>
> > > >>>>
> > > >>>> well, if you insist:
> > > >>>> http://www.bhphotovideo.com/c/product/686604-REG/Blackmagic_Design_CONVMUDC_Mini_Converter_UpDownCross.html
> > > >>>>
> > > >>>> that's an extra 200$ gift to BMD
> > > >>>>
> > > >>>> BG
> > > >>>> http://www.finale.tv
> > > >>>>
> > > >>>>
> > > >>>> From: Lou Wirth <loutv@>
> > > >>>> To: Avid-L2@yahoogroups.com
> > > >>>> Sent: Thursday, December 12, 2013 10:22 AM
> > > >>>> Subject: Re: [Avid-L2] HD to SD converter
> > > >>>>
> > > >>>>
> > > >>>> Thanks but I want SDI output. That is what I am having trouble finding. SDI HD in and SDI SD out.
> > > >>>>
> > > >>>>
> > > >>>> Lou Wirth Productions
> > > >>>> 500Tamal Plaza, Suite 522
> > > >>>> Corte Madera, CA 94925
> > > >>>> www.louwirth.com
> > > >>>> 415-924-9411p
> > > >>>>
> > > >>>>
> > > >>>>
> > > >>>>
> > > >>>>
> > > >>>>> On Dec 12, 2013, at 10:18 AM, Bogdan Grigorescu <bogdan_grigorescu@> wrote:
> > > >>>>>
> > > >>>>>
> > > >>>>>
> > > >>>>> this:
> > > >>>>> http://www.bhphotovideo.com/c/product/558908-REG/Blackmagic_Design_CONVMASA_Mini_Converter_SDI_to.html
> > > >>>>>
> > > >>>>> BG
> > > >>>>> http://www.finale.tv
> > > >>>>>
> > > >>>>>
> > > >>>>> From: Lou Wirth <loutv@>
> > > >>>>> To: "Avid-L2@yahoogroups.com" <Avid-L2@yahoogroups.com>
> > > >>>>> Sent: Thursday, December 12, 2013 9:19 AM
> > > >>>>> Subject: [Avid-L2] HD to SD converter
> > > >>>>>
> > > >>>>>
> > > >>>>> Losing my FS1 tomorrow. It was a loner. What is a simple, inexpensive way to down covert my HD to my Sony 20M4U monitor. I still love using that thing along with my other monitors.
> > > >>>>>
> > > >>>>> thanks
> > > >>>>>
> > > >>>>> Lou
> > > >>>>> Lou Wirth Productions
> > > >>>>> 500Tamal Plaza, Suite 522
> > > >>>>> Corte Madera, CA 94925
> > > >>>>> www.louwirth.com
> > > >>>>> 415-924-9411p
> > > >
> > > >
> > >
> >
> >
>
| Reply via web post | Reply to sender | Reply to group | Start a New Topic | Messages in this topic (14) |
No comments:
Post a Comment